2020 RAM 1500 AMP STEPS INSTALL
2020 RAM 1500 AMP STEPS DRIVERS
2020 RAM 1500 AMP STEPS DRIVER
2020 RAM 1500 AMP STEPS FULL

Extruded aluminum steps with a textured powder-coat finish for maximum grip and durability.Precision, zero-maintenance stainless-steel pivot pins.High-strength, die-cast aluminum-alloy linkage arms, anodized and Teflon®.

2020 RAM 1500 AMP STEPS FULL

The original AMP Research PowerStep™ is proven to perform in severe driving conditions and is backed by a full 5-year/60,000 mile warranty – the best in the business. When the doors close, it retracts just as smoothly, streamlining the vehicle profile with no loss of ground clearance. Ditto its industry-leading 5-year/60,000-mile warranty.ĭesigned and built exclusively in the USA, the genuine AMP Research PowerStep™ seamlessly extends when any door is opened, giving a rock-solid, safe and convenient step up into your truck. Its handsome design, all-weather performance and legendary reliability set the industry standard. That’s why AMP Research invented POWERSTEP™, the automatic, electric-powered running board that instantly extends when you open your door, and then hides itself safely out of sight when the doors close for improved ground clearance, aerodynamics and appearance. GETTING INTO YOUR TRUCK SHOULDN’T FEEL LIKE CLIMBING MOUNT EVEREST. With tips I learned I think you can do it in 1.5 hours.AMP Research 19-/3500 GAS PowerStep Electric Running Boards Return home, grab your favorite glass and tune into Dram of the Day with me 2 hours.

2020 RAM 1500 AMP STEPS INSTALL

Wire tie everything, install clips, put back screws in dash.Įnjoy your easy climb into your beast. Now connect the power to the distribution block that you ran previously under the hood but didn't connect. Slide them on existing bolts and use 6 provided nuts (either side to secure). Lift them by the step, not the cross bar (sticker on crossbar tells you this right out of the box). To mount the boards, motors always go forward. Plug in your boards as soon as they are mounted. The ground wire (with ring spade) goes on grounding spade in kick panel as well. Instructions do a good job visually locating this. The small clip coming out of the black harness can go into any open slot on the factory module located in driverside kick panel. The only remaining things to do with regard to wiring are: Use the 3 push clips provided to mount the module.

You will see a flat piece of sound deadening material. It is under the dash (driver side) to the left of the brake pedal. The mounting location for the module was not clear for me. Black is on left and gray is on right if you are looking at the top of the module and the ports are pointed at you. By process of elimination I plugged Brown into BG and the brown and black into BN/BG.

Then you are left with Brown and Black and Brown. TIP: for the gray harness, I'm either color blind or their color abbreviations don't make sense to me. Some of these spades also go into the black (smaller harness). TIP: be very carefully to plug them in correctly they are a nightmare to remove once they click into place. They provide an automotive plug (gray) for you to plug these into. The piece of the harness you snaked through the firewall has spades. They are just plastic and will bend back as soon as you push them from the other side. You can push on them from the back side (looking from under the hood to flex them and keep the wire out of the hot zone.

2020 RAM 1500 AMP STEPS DRIVER

Route the driver side down the wheel well. Once removed the passenger side cable can be routed by tucking it up into the channel. The first piece is a pin that expands the second piece. Use flatblade screwdriver to remove the top piece of each clip. There is a wire channel up top (instructions show it). The longer one goes to the passenger side. Don't connect it to the lug at this time. You are on the side of the battery so run it to the power distribution block in front of the battery. The other side of the largest harness (now under the hood) has three segments. A little 3M electrical tape on the side of the largest harness with the spades (not plugs) and it attached to the coat hanger and pulled right through (from outside to inside). Fished it through the sliced grommet from the inside to the outside (under the hood). I removed the 2 screws at the bottom of the driver's side dash and pulled out the the remaing clips (pull straight out. The grommet must be sliced on the border to fit the wires through.

2020 RAM 1500 AMP STEPS DRIVERS

The first part (largest harness) is snaked through the firewall gromet on the drivers side. I didn't remove the wheels but I did loosen all the screws on one fender well. You do NOT need to remove the wheels and fender wells on this truck as the instructions suggest. Very pleased but thought I would share a few tips to avoid time sucks that I fell victim to.

2020 ram 1500 amp steps